8 tips on 400 101 ccie

400-101 Royal Pack Testengine pdf

100% Actual & Verified — 100% PASS

Unlimited access to the world's largest Dumps library!

Download 400-101 Dumps Free

Product Description:
Exam Number/Code: 400-101
Exam name: CCIE Routing and Switching (v5.0)
n questions with full explanations
Certification: Cisco Certification

HOW TO GET 400-101 Exam PDF Collection Free?

Our pass rate is high to 98.9% and the similarity percentage between our 400 101 pdf study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco ccie 400 101 exam in just one try? I am currently studying for the Cisco ccie 400 101 dumps exam. Latest Cisco ccie 400 101 dumps Test exam practice questions and answers, Try Cisco 400 101 pdf Brain Dumps First.

P.S. Guaranteed 400-101 testing material are available on Google Drive, GET MORE: https://drive.google.com/open?id=1IW-FBjIGklMU6wt1CVbJF66pb-8K-oca


New Cisco 400-101 Exam Dumps Collection (Question 13 - Question 20)

New Questions 13

What is used to acknowledge the receipt of LSPs on a point-to-point network in IS-IS?

A. hello

B. CSNP

C. PSNP

D. IIH

E. CSH

Answer: C



New Questions 14


Refer to the exhibit If R1 and R2 cannot establish an OSPF neighbor relationshipwhich two action can you take to Choose two

A. Configuration PPP authentication under the R2 Gigabitethernet 0/1 interface

B. Change the ip local pool command on R2 to ip local pool pool! 192 168 12 192 168 1.5 I"

C. Configuration R1 to send the username and password on the Dialer 1 interface

D. Change the PPP authentication to CHAP authentication

E. Configure PPP encapsulation under the R1 virtual-templat interface

Answer: C,E



New Questions 15


Refer to the exhibit. R1 and R2 have been configured as BGP neighbors, but their session is stuck in active. Which action can you take that will enable a session to beestablished?

A. Enable synchronization on R1 R2

B. Issue the neighbor 10.1.12 .2 activate command on R'1

C. Configure 10.1.12.1 as the BGP router 10 on R1

D. Configure a neighbor relation ship with the Loopback0 address of R1 on R2

Answer: D



New Questions 16

Refer to the exhibit.

What is the effect on the network when you apply these configuration to RI and R2?

A. Asymmetric routing occurs because the bandwidth and delay K value settings are mismatched.

B. The interface bandwidth and delay settings adjust automatically to match the new metric settings

C. The neighbor adjacency between R1 and R2 temporarily resets and then reestablishes itself.

D. R1 and R2 fail to form a neighbor adjacency.

Answer: D



New Questions 17

Which three conditions must be met for the IP routing state of an interface to be up?(choose three.

A. The interface must have a known IP address

B. Active IP routing must be enabled

C. Cisco express forwarding must be enabled

D. Cisco discovery protocol must be enabled on the inter face

E. A backup interface must be defined

F. The interface line-protocol state must be up

Answer: A,B,F



New Questions 18

Exhibit:

Refer to the exhibit. Which three statements about the output are true? (choose three.)

A. Group 224.0.1.40 is a reserved address , and it should not be used for multicast user data transfer.

B. One or more multicast groups are operating in PIM multicast user data transfer.

C. Group 239.192.1.1 is reserved address, and it should not be used for multicast user data transfer.

D. A multicast receiver has requested to join one or more of the multicast groups.

E. This switch is currently receiving a multicast data stream that is being forwarded out VLAN 150.

F. One or more of multicast data streams will be forwarded out to neighbor 10.85.20.20.

Answer: A,D,E



New Questions 19

Which two statements about IS-IS neighbor adjacencies are true?(Choose two )

A. Each device must have the same 6-type systemID

B. Neighboring devices must have the same level.

C. If the ignore-mtu command is configured on both devices.the devices can have different MTU settings

D. Each device's 4-type router ID must be unique.

E. Level 1 devices must be in the same area

Answer: B,E



New Questions 20

Which keychain cryptographic algorithm is supported by the IS-IS routing protocol?

A. MD5

B. HMAC-SHA1-12

C. HMAC-SHA1-20

D. HMAC-MD5

Answer: D



Recommend!! Get the Guaranteed 400-101 dumps in VCE and PDF From Examcollectionplus, Welcome to download: https://www.examcollectionplus.net/vce-400-101/ (New 427 Q&As Version)


[TRY FREE] BUY 400-101 Full version( pdf+software ):
https://www.exambible.com/400-101-exam/